Description

blade width .04″. If you need to remove a metal terminal from its plastic connector, this genuine Aptive/Delphi tool allows you to depress & release the locking tang on most terminals used by GM from 1950-80s. Not for use with Weather-Pak terminals. Made in USA.

Additional information

Lectric Limited Part #: 12094429
OEM Part #: 12094429
WebID Part #: id-12094429-0064
Weight: 0.1 lbs

You have not selected a vehicle

Also fits: This fit is only a guideline. Please verify the fit by entering your specific vehicle.

Make	Model	Years
AMERICAN MOTORS	ALL MODELS	1956 - 1983
BUICK	FULLSIZE/RIVIERA	1936 - 1996
BUICK	SKYLARK/SPECIAL/GRAN SPORT	1961 - 1987
CADILLAC	FLEETWOOD/SEVILLE/DEVILLE/EL DORADO	1941 - 2000
CHEVROLET	CAMARO	1967 - 2002
CHEVROLET	CHEVELLE/EL CAMINO/MONTE CARLO/MALIBU	1964 - 1988
CHEVROLET	CHEVY II/NOVA	1962 - 1979
CHEVROLET	CORVAIR	1960 - 1969
CHEVROLET	CORVETTE	1953 - 2012
CHEVROLET	FULLSIZE 1955-57	1955 - 1957
CHEVROLET	FULLSIZE 1958 & UP	1958 - 1996
CHEVROLET	FULLSIZE PRE 1955	1929 - 1954
CHEVROLET	MONZA	1975 - 1980
CHEVROLET	S10 SERIES: PICK-UP/BLAZER	1982 - 2004
CHEVROLET	TRUCK/PICK-UP/SUBURBAN/BLAZER	1929 - 2007
CHEVROLET	VEGA	1970 - 1977
CHRYSLER	IMPERIAL	1960 - 1974
CHRYSLER	NEWPORT/NEW YORKER/TOWN & COUNTRY/300	1960 - 1974
DE SOTO	ALL MODELS	1959 - 1961
DODGE	CHALLENGER	1970 - 1974
DODGE	CORONET/CHARGER/SUPER BEE/DAYTONA/330/440	1959 - 1974
DODGE	DART/DEMON/SWINGER	1960 - 1976
DODGE	POLARA/MONACO/CUSTOM 880/880	1960 - 1974
DODGE	TRUCK A100 SERIES: PICK-UP/VAN	1963 - 1970
DODGE	TRUCK D/W 100-350 SERIES: PICK-UP/TOWN/RAMCHARGER	1963 - 1972
FORD	FAIRLANE/TORINO/COBRA	1957 - 1974
FORD	FALCON	1960 - 1970
FORD	MUSTANG	1964 - 1973
FORD	THUNDERBIRD	1955 - 1966
GMC	S15 SERIES: PICK-UP/SONOMA/JIMMY	1982 - 2004
GMC	TRUCK	1947 - 2007
HOLDEN	ALL MODELS	1963 - 1979
JEEP	CJ/YJ	1966 - 1996
MERCURY	COMET/CYCLONE/MONTEGO	1960 - 1974
MERCURY	COUGAR	1967 - 1973
OLDSMOBILE	CUTLASS/442/F-85	1961 - 1988
OLDSMOBILE	FULLSIZE	1940 - 2000
OLDSMOBILE	TORONADO	1966 - 1985
PLYMOUTH	BARRACUDA	1964 - 1974
PLYMOUTH	BELVEDERE/SAVOY/SATELLITE/GTX/ROAD RUNNER/SUPER BIRD	1959 - 1974
PLYMOUTH	FURY/VIP/SUBURBAN	1959 - 1974
PLYMOUTH	VALIANT/DUSTER/SCAMP/SIGNET	1960 - 1976
PONTIAC	FIERO	1984 - 1988
PONTIAC	FIREBIRD/TRANS AM	1967 - 2002
PONTIAC	FULLSIZE/GRAND PRIX	1940 - 2000
PONTIAC	TEMPEST/LEMANS/GTO/T-37/GRAND AM/VENTURA	1961 - 1981
STUDEBAKER	ALL MODELS	1955 - 1964

TECH NOTES:

To REMOVE a metal terminal from its plastic connector:
1. Begin with the plastic connector facing towards you, meaning the wire(s) are going away from you.

2. Gently insert this terminal removal tool into the small notch of the connector's terminal cavity. It should not require much force. You should feel the tool bottom out solidly in the connector approximately 1/4 inch. The idea is to depress the terminal's locking tang.

3. With the removal tool still inserted fully in the cavity, gently pivot the tool to depress the locking tang. NOTE: Some terminals have locking tangs on 2 sides. Repeat Steps 2 & 3 on the other side of the terminal, if necessary.

4. Pull on the wire to remove it. If the wire is not EASILY removed, repeat Step 3.

To RE-INSERT a metal terminal into its plastic connector:
1. Before re-inserting the wire, gently and slightly pry open the terminal's locking tang(s) that was previously depressed. You can use this tool to pry open the locking tang(s).

2. Insert the terminal into the connector. You may hear/feel a "click".

3. Pull back on the wire to make sure that it is locked-in and will not pull out of the connector.